248: Sunday 5th May 2103

Started on a beautiful Saturday morning by removing the inner door panel. I had about 10 or 11 holes in the door where the clips for the old trim panel were. As this was not needed and would look silly now I had to fill these. With a fresh mix of fibre glass, I took my plastic scraper with some fibre glass on it inside the door and covered the holes from behind. While this was drying I went out to the summer house at the back of garden and got the other side skirt. I took off the old side skirt and trimmed a strip from it with the clips attached, fitted the strip back on then offered up the new panel. The panel would not go anywhere near the body with the clips strip attached. I took the clip strip off and offered the panel up again and checked the gap. It was a good fit, much better than the other side. By this time the fibre glass on the door was dry and I ground back the excess and spray painted with primer to stop any rusting. Then the rain came, and then the Hail came. So I went indoors and Twister was on TV, so I sat and watched, and that was Saturday.

----
Sunday was a beautiful morning, the sun was shining and I got reasonably early start (10 am). I filled the holes in the door that were fibre glassed ground back and primed the day before. I also filled the rear bumper panel as there was a dip where I had got carried away with the sander machine. I carried on with adjusting the clip strip on the other side skirt while the filler was drying. I cut more off the strip and made it so the clips were only secure on one side and could be bent in. I took one clip off altogether and cut the strip into 2 parts. The rear part was still too big, so I decided to just have one clip at the rear. I reworked one clip so it would fit under the trim, then drilled holes to mount the panel with screws. With the side panel nice and secure and fitted generally I marked the top of the trim where it meets the door ready to be trimmed later. This is necessary in order to make the door open without catching as the panel needs to drop down a few millimeters. The process was mostly the same as the other side except I kept some of the clips together on a strip of plastic to make is easier to mount them. The filler on the door dried and I rubbed it down to make it smooth. It took me 2 goes to apply the filler as it was so hot that it was going hard quite quickly. I sanded it back smooth, but the rear bumper needed another layer, so I mixed some more and put it on. More sanding and then  was ready to mask up the windows and other trim so they didn't get painted. I put primer over the bottom half of the door, generally covering my work and the rear bumper repair. A light sand by hand and I was ready to prep for painting. This involved a quick dust off with a dry micro-fibre cloth and a tissue wipe with white spirit to remove any trace of grease or other chemicals. I also sprayed a bit of the rear bumper where it had picked up some over spray of primer from another day. I sprayed the repair on the rear bumper and the rear quarter panel. I sprayed inside the edge of the door over the polyurethane sealant and then the outside of the door. I didn't have enough paint in the can to finish the door, but I got most of it done and it is not super important to be finished at this stage as  have plenty more painting to do and I can go over it again then. It is starting to look better and better.

2 comments:

  1. I really enjoyed this post. You describe this topic very well. I really enjoy reading your blog and I will definitely bookmark it! Keep up the interesting posts!



    Lone Mountain Truck Leasing

    ReplyDelete
  2. I am glad to hear it. Sorry I took so long to reply, but I don't check my email very often. The best way is to use my facebook link on the right side of this page. I use facebook several times each day. Also you can become a follower again using the panel on the right side of this page. This can be set to give you automatic prompts by email etc when there is a change. If you friend me on facebook then I always post updates on their too. So now you just need to read the other 247 pages.....

    ReplyDelete